Idioma: Español english
Predefinidos: Default Face_ltd Load Download Cookies ← Save
Alternative throttle control algorithm : Instant change Smooth change speed control & speed cruisepower control & power cruisequadratic power control at S & cruise, speed control at D/Eco & cruiseline power control & speed cruisequadratic power control & speed cruiseline power control at S & speed control at D/Eco/cruisequadratic power control at S & speed control at D/Eco/cruise Enable throttling without disable of the cruise control ? Changes the stock type of throttle algorithm to alternative
Motor start speed: ? Minimum speed in km/h before the engine will start
Cruise control delay: ? How many seconds it takes for cruise control to kick in
Toggle cruise state by short throttle tap :Enable from the speed, km/h (0-100): Default cruise speed after turn on, km/h (0-100): Lever position above which the cruise can be activated after lever is released (1-125): The time from the start of lever push, during which lever must be completely released (1-255): ? Adds cruise toggle mode by short tap the throttle lever without changing the stored speed
Intensity of current change when using throttle lever: ? Sets the step size in mA to change the current to the new when you press the throttle lever (smaller value - more smoothness)
Brake lever params: Brake lever limit (1-125): Minimum brake phase current: Maximum brake phase current: ? Change the start position of the brake lever and the range of braking currents with the minimum and maximum position of the lever
Intensity of current change when using brake lever: ? Sets the step size in mA to change the current to the new when you press the brake lever (smaller value - more smoothness)
KERS min speed: ? Speed in km/h at which the scooter will start braking on it's own when the engine is not active. You will still have recuperative braking when using the brake !
Anticlonk after free-ride ? Removes clonks in the motor wheel when useing the controls after free-ride
Correcting free-ride KERS levels: Stock multipliers - 6/12/20Half-stock multipliers - 3/6/101/3-stock multipliers - 2/4/8 ? Change KERS power multipliers during the free-ride that are set in the scooter KERS settings low/medium/high
Switching free-ride KERS levels depending on the modes Eco/D/S = low/medium/highEco/D/S = medium/low/highEco/D/S = high/medium/lowEco/D/S = high/off/off ? Sets the free-ride KERS level (low/medium/high) depending on the modes (Eco/D/S)
Turn off KERS braking during free-ride ? Turn off KERS braking at free-ride. You will still have recuperative braking when using the brake !
Maximum speed in S mode: ? Maximum speed limit in S mode. Not valid when choosing power control algorithms !
Maximum speed in D mode: ? Maximum speed limit in D mode. Not valid when choosing power control algorithms !
Maximum speed in Eco mode: ? Maximum speed limit in Eco mode. Not valid when choosing power control algorithms !
Alternative speed limits : If headight On If headlight Off Maximum speed in S mode: Maximum speed in D mode: Maximum speed in Eco mode: ? Activate alternative speed limits switching by the condition of the headlight. Not valid when choosing power control algorithms !
Current limit for S mode depending on temperature, capacitance and voltage: mA (755W) ? The maximum current value in S mode. It takes precedence over the current Maximum battery current !
Current limit for D and Eco modes depending on temperature, capacitance and voltage: mA (661W) ? The maximum current value in D and Eco modes. It takes precedence over the current Maximum battery current !
Current value for S mode: Maximum battery current: mA (755W) ? Change the maximum battery current for S mode
Current value for D mode: Maximum battery current: mA (506W) ? Change the maximum battery current for D mode
Current value for Eco mode: Maximum battery current: mA (205W) ? Change the maximum battery current for Eco mode
Lower temperature limit for power limitation: ? Minimum temperature in degrees below which power limits will be applyed
Higher temperature limit for power limitation: ? Maximum temperature in degrees above which power limits will be applyed
Lower battery voltage limit for power limitation: ? Minimum voltage in volts below which power limits will be applyed
Remove power limit ? Skip temporary power limitation with active movement. Set a half-value of maximum battery currents !
Allow to set cruise at high power ? Remove prohibition on cruise activation at high current power on the motor-wheel
Skip cruise set at maximum throttle ? Skip cruise control set at maximum throttle lever position
Boot with ECO mode ? The scooter will always start in ECO mode
Turn off D and S modes ? Disables the mode button
Use overvoltage battery up to: ? Set the voltage in volts when using an overvoltage battery
Remove charging mode ? Fixes issue of scooter going into charge mode with an external battery connected in parallel
Change ESC<->BMS baud rate to 76800 ? Change the exchange rate of the main controller with the BMS to 76800. Only if you use the compatible open source BMS !
No BMS data battery support : Remove temperature/overcharge check at braking Remove minimal temperature check Remove maximal temperature check Remove voltage check Remove capacity check Remove BMS error indication Enable fake full charge level at display ? Connecting a third-party main battery without data exchange. No battery control !
Idle time to shutdown: ? Set the idle time in seconds (1-325) to automatically shutdown
Lock time to shutdown: ? Set the lock time in minutes (1-5965) to automatically shutdown
Don't shutdown scooter at the lock mode ? Don't shutdown scooter at the lock mode
Full battery postcharge time: ? Set additional charging time in seconds after reaching 100% battery (1-60000)
Extra time before shutdown after postcharging: ? Set the time in seconds (1-60000) before shutdown after additional charging
Cruise beep type: no beepshort beepmiddle beepdouble short beeplong beep ? Changes the sound when you turn on the cruise by holding the throttle lever
Add beep to drive modes select : For S mode:no beepshort beepmiddle beepdouble short beeplong beep For D mode:no beepshort beepmiddle beepdouble short beeplong beep For Eco mode:no beepshort beepmiddle beepdouble short beeplong beep ? Adds beeps when switching modes
Charge connect beep type: no beepshort beepmiddle beepdouble short beeplong beep ? Changes the sound when charging is connected
Charge disconnect beep type: no beepshort beepmiddle beepdouble short beeplong beep ? Changes the sound when charging is disconnected
Turn off beep type: отключенshort beepmiddle beepdouble short beeplong beep ? Changes the sound when turn off the scooter
Add beep to end of charging ? Adds beep at the end of charging when the scooter is turned on
Backlight flashing frequency: ? Changes the flashing frequency of the backlight when braking (1-100). Lower value - higher frequency
Remove flashing of the backlight during free-ride ? Removes backlight flashing at free-ride
Add a beep when using the brake : Set the position of the brake lever (0-110) above which there will be a sound signal: ? Adding a sound signal when the brake lever is above the set value
Add a double long signal when the specified percentage of charge is reached : When the battery charge percentage is (61 is a halfway): ? Add a double sound signal when the specified percentage of battery charge is reached
Full battery predicted distance : For S mode: For D mode: For Eco mode: ? Sets the predicted distance in selected mode with a fully charged battery in km
Add value in percent to increase 10" wheel speed and distance % ? Enter value for correct recalculation of speed and distance when using 10" wheels
Turn on the strobe Only in motion When stopping, turn on the headlamp When stopping, turn off the headlamp Double blink settings: First flash: Turn on in step Turn off in step Second flash: Turn on in step Turn off in step Start the flash cycle again when the step is reached ? Activates strobe flashing when the option "Taillight is always on" is on. Since the BLE controller has its own polling frequency, you need to select the parameters.Send me the good options set to e-mail.
Swap speed and charge output on the display : Only in the selected mode Eco modeD modeS mode Swap Don't swap Only when stopped ? Swaps the output of speed and charge percentage on the display
Replace throttle error 14 with errors: 41 - throttle sensor level too low, 42 - throttle sensor level too high ? Specifies throttle position sensor errors by adding errors 41 and 42. Error 14 remains for pressed throttle when the scooter is turned on
Replace brake error 15 with errors: 51 - brake sensor level too low, 52 - brake sensor level too high ? Specifies brake position sensor errors by adding errors 51 and 52. Error 15 remains for pressed brake when the scooter is turned on
Increase the time before shutdown from one minute to three if errors 14 and 15 occur ? Increases the time, allowing to flash the working firmware while holding the brake or throttle lever when the current firmware hangs
Swap main button functions ? Set the mode change to a single button tap, and the headlight toggle to double tap
Enable write permissions for internal registers ? Allows writing values to internal registers through third-party applications
Use ONLY the following app to flash your modified FW: M365 DownG XG Mod When migrate to generator's firmwares, flash them TWICE! Migrate from firmwares for M365 only from version 1.4.1 or higher !!!Use standard flashers to factory firmware rollback